# DIY GPRS Particles Kit V0.1
Label: DIY Gas Monitor
---
# Introduction
There's no need to worry about the incompatibility issue when configure network by 8266 nodemcu airkiss. This is a set of open-source DIY kit that can monitor particles once power up.
Based on the content of [GPRS 颗粒物检测仪DIY教程3 GPRS 颗粒物检测仪][1] and equipped with a customized bottom board, the GPRS particle kit V1.0 has been done.
For all open source files, please refer to [GPRS 颗粒物检测仪DIY教程3 GPRS 颗粒物检测仪][1]
The main work of V1.0 is to add a bottom board, which can make wire connection much easier.
![IMG_20170814_173919.jpg-2321.2kB][4]
# Hardware & Costs
Cost: about 210 RMB
Hardware | Costs | Description
----|----------|-----|
AirM2MS1(GPRS Luat version) |About 50 RMB|GPRS Uplink, Cooperate with luat development environment
YEETC A4 or Plantower G5| About 75 RMB | Particle Sensor
HMI lcd serial port screen |35 RMB |
SI7021 Module|10 RMB|
Annual fee for IoT service|22 RMB|
Board&Wires|5 RMB|
# Monitor by WeChat
Plug S1 on the board, power on, if you insert sim card, about half a minute later, there will appear a two-dimensional code. Directly scan this two-dimensional code by WeChat to complete the binding. Then, you can use it.
**Note: all contents are open sourse, please refer to [GPRS 颗粒物检测仪DIY教程3 GPRS 颗粒物检测仪][1]**
![IMG_20170814_173650.jpg-2952.8kB][3]
If it can connect to network successfully, "particle detection" will be displayed on the LCD screen.
![IMG_20170814_173919.jpg-2321.2kB][4]
Of course, you can change it by WeChat.
![QQ图片20170814174420.png-792.7kB][5]
![QQ图片20170814174605.png-122.6kB][6]
Then the words on LCD screen has been changed accordingly.
![IMG_20170814_173324.jpg-4598.5kB][7]
# Monitor on DeviceBit
直接把S1 模块上面的IMEI 作为sn 添加在乐联网系统,就可以直接通过乐联网来监控数据了。
Directly add IMEI on module S1 as Sn on DeviceBit, then you can monitor the data online anytime or anywhere
[1]: http://www.jianshu.com/p/97da5fa42509
[2]: http://static.zybuluo.com/guanvee/6s94wrzgiv3p650z8spuwt1y/IMG_20170814_173324.jpg
[3]: http://static.zybuluo.com/guanvee/eusaq8lyim7y572r1qz6gbtz/IMG_20170814_173650.jpg
[4]: http://static.zybuluo.com/guanvee/p9f5qgu7ammomxxe9amudqxi/IMG_20170814_173919.jpg
[5]: http://static.zybuluo.com/guanvee/zpjjg817djbz0f01y4f26ah8/QQ%E5%9B%BE%E7%89%8720170814174420.png
[6]: http://static.zybuluo.com/guanvee/zyplk7mzdlokvd8rnquvart2/QQ%E5%9B%BE%E7%89%8720170814174605.png
[7]: http://static.zybuluo.com/guanvee/ijts0r55eq0bg1hzd4j0w16c/IMG_20170814_173324.jpg
- DeviceBit User Manual
- Quick Start
- 1. Add A Device
- 2. Add a new sensor or controller
- 3. Data Upload Simulation
- 4. WeChat Alert
- 5. Email Alert
- 6. Data Reports
- 7. Account Settings
- 8. WeChat
- 9. Email Auto-sending
- 10. Email Report
- 11. Control Scheme
- 12. Trigger
- 13. MQTT
- 14. Modbus
- 15. Agent
- 16. Credits
- DeviceBit Open Source Tutorials
- 1. DIY WiFi Particles Monitor
- 2. DIY WiFi Particles & HCHO Monitor
- 3. DIY GPRS Particles Monitor
- 4. GPRS Particles Kit V0.1
- 5. WiFi Socket
- Applicaton Doc
- DTU Tutorial 1: Overview
- DTU Tutorial 2: Using DTU to connect JSY-149 single-phase meter to DeviceBit
- DTU Tutorial 3: Using Python+Openwrt DIY DTU & Connect DeviceBit
- DTU Tutorial 4 DIY Low-cost DeviceBit GPRS DTU
- DTU Tutorial 5: DIY Low-cost DeviceBit WIFI DTU
- DeviceBit Other Platform